Ampetronic

CLS2-R1

Concourse Induction Loop Driver

Product code: CLS002-R1

Description

CLS2-R1 Concourse induction loop driver

Applications include:

• Railway station platform waiting areas • Tram station waiting areas • Bus shelters • Bus station waiting areas • Ski-lift waiting areas • PA enabled Taxi ranks

Features

• Quick and simple to install
• Complies with Railway EN50121-4 safety standard
• Area coverage to >400m2
• Configurable inputs designed specifically for a range of PA systems
• Panel or enclosure mounting
• Metal Loss Correction
• 5 Year warranty
• Preconfigured connections
• Free Technical support

Technical specifications

The CLS2-R1 enclosure is designed for simple, permanent installation. Connections are preconfigured and controls are accessible underneath the removable lid to deter unwanted post commissioning adjustments with indicator LEDs clearly visible on the front panel. The case is designed to make access simple, and to ensure the amplifier can be installed in the most constrained spaces.

Mounting:

Designed for vertical panel or wall mounting mounting using 4 screws (6 holes provided). The CLS2-R1 is compact enough to fit on a 1U rack tray with feet removed.

Enclosure access:

Removable lid, secured by 4 Phillips PH2 screws. Lid can be removed completely if required, for ease of access.

Cable connections:

Input 1 is suitable for use with balanced microphone or balanced low power line signals. Inputs 2 & 3 are preconfigured to suit a range of PA Systems. AC power input and fuse are located in the IEC power connector. The unit also features an M6 ground stud.

Indicators:

3 LED indicators are visible with the case open or closed:
• AGC (Amber) LED lit when input signal is activating the automatic gain control
• Current (Green) LED lit when current is running in the loop
• Power (Green) LED lit when the unit has power controls four controls are located to be accessed only with the lid open, all screwdriver adjustable.
• Level controls for inputs 1, 2 and 3
• Metal loss correction
• Loop drive current

Perimeter Loops – Area Coverage (maximum):

Room aspect ratio 1:1 2:1 3:1
Maximum area m2 250 310 400

For any Induction Loop System, area coverage is dependent on several factors. Please check these assumptions and contact Ampetronic for advice if required:
• Loop must be 1-2m above or below the receiver (hearing aid) height
• There should be no metal structures in the plane of the loop
• Sufficient voltage to drive the loop – check the cable table below

Maximum Cable Length:

The CLS2-R1 is designed for SINGLE TURN loops for optimum audio quality:
• Loops with DC resistance from 0.2Ω
• Impedance up to a maximum of 1.3Ω
Maximum cable length is dependent on cable type and on the application:

Cable type Normal use (m) Transient speech (m)
1.0mm2 copper 49 57
2.5mm2 copper 67 85
4.0mm2 copper 70 91
1.8mm2 flat copper tape 87 101

Inputs:

Input 1 Input 1 Balanced Mic, balanced or unbalanced line
Input impedance 10kΩ per side
Min level (MIC / Line -73dBu / -31dBu
Max level (MIC / Line) -37dBu / +5dBu
Phantom voltage MIC only +12V
Input 2 Isolated 100V line or low impedance mono
or stereo speaker
Input impedance 100V Line / spkr 120kΩ / 7.8kΩ
Min level 100V Line / spkr +14dBu / -9dBu
Max level 100V Line / spkr >+47dBu / >+27dBu
Input 3 Isolated 100V line or low impedance mono
or stereo speaker
Input impedance 100V Line / spkr 120kΩ / 7.8kΩ
Min level 100V Line / spkr +14dBu / -9dBu
Max level 100V Line / spkr >+47dBu / >+27dBu
AC power input supply 230V 30Ws 45-65Hz
110V option available
Connected via chassis mounted screw terminal
block
Input fuse T250mA

Outputs:

Drive voltage >7.1VRMS – 10.0Vpk
Drive Current 1kHz sine wave >4.9ARMS 7.0Apk
Continuous pink noise 2.3ARMS 7.0Apk
Short term peaks >7ARMS 10Apk
Minimum Loop Resistance 0.2Ω
Maximum Loop Impedance 1.3Ω

THERMAL HEAT CHART

Idle 1/6 peak Output Current 1/3 peak Output Current Full Power
Driver Channels Current (ARMS) Load Resistance (Ohms) AC In (W) BTU AC In (W) BTU AC In (W) BTU AC In (W) BTU
CLS1 1 3.5 1.0 4 14 15 47 27 77 45 111
CLS2 1 4.9 1.0 5 17 19 58 35 91 63 131

Audio system:

Frequency Response 80Hz to 6.3kHz ±3dB
Distortion THD+N
Automatic Gain Control (AGC) Optmised for speech. Dynamic range >36dB
Metal loss correction (MLC) 0 to 3dB per octave frequency correction
(1kHz remains constant). Control mounted on PCB.

Physical:

Cooling Natural convection
Environment IP20, -10°C to +40°C
Dimensions W, H, D: 200mm, 200mm, 44mm
Weight 1.8kg
Mounting Wall mounting, secured by 4 screws

More in this family