
Açıklama
CLS2-R1 Terminal Giriş Alanı İndüksiyon Döngü Sürücüsü
Uygulama Alanları:
• Tren istasyonu platform bekleme alanları • Tramvay istasyonu bekleme alanları • Otobüs durakları • Otobüs terminali bekleme alanları • Kayak lifti bekleme alanları • Seslendirme sistemli taksi durakları
Özellikler
- Hızlı ve kolay kurulum
- Demiryolu EN50121-4 güvenlik standardına uygundur
- 400 m2'den fazla alan kapsama alanı
- Çeşitli seslendirme sistemleri için özel olarak tasarlanmış yapılandırılabilir girişler
- Panel veya muhafaza montajı
- Metal Kaybı Düzeltme
- 5 Yıl garanti
- Önceden yapılandırılmış bağlantılar
- Ücretsiz Teknik destek
Teknik özellikler
The CLS2-R1 enclosure is designed for simple, permanent installation. Connections are preconfigured and controls are accessible underneath the removable lid to deter unwanted post commissioning adjustments with indicator LEDs clearly visible on the front panel. The case is designed to make access simple, and to ensure the amplifier can be installed in the most constrained spaces.
Mounting:
Designed for vertical panel or wall mounting mounting using 4 screws (6 holes provided). The CLS2-R1 is compact enough to fit on a 1U rack tray with feet removed.
Enclosure access:
Removable lid, secured by 4 Phillips PH2 screws. Lid can be removed completely if required, for ease of access.
Cable connections:
Input 1 is suitable for use with balanced microphone or balanced low power line signals. Inputs 2 & 3 are preconfigured to suit a range of PA Systems. AC power input and fuse are located in the IEC power connector. The unit also features an M6 ground stud.
Indicators:
3 LED indicators are visible with the case open or closed:
• AGC (Amber) LED lit when input signal is activating the automatic gain control
• Current (Green) LED lit when current is running in the loop
• Power (Green) LED lit when the unit has power controls four controls are located to be accessed only with the lid open, all screwdriver adjustable.
• Level controls for inputs 1, 2 and 3
• Metal loss correction
• Loop drive current
Perimeter Loops – Area Coverage (maximum):
| Room aspect ratio | 1:1 | 2:1 | 3:1 |
| Maximum area m2 | 250 | 310 | 400 |
For any Induction Loop System, area coverage is dependent on several factors. Please check these assumptions and contact Ampetronic for advice if required:
• Loop must be 1-2m above or below the receiver (hearing aid) height
• There should be no metal structures in the plane of the loop
• Sufficient voltage to drive the loop – check the cable table below
Maximum Cable Length:
The CLS2-R1 is designed for SINGLE TURN loops for optimum audio quality:
• Loops with DC resistance from 0.2Ω
• Impedance up to a maximum of 1.3Ω
Maximum cable length is dependent on cable type and on the application:
| Cable type | Normal use (m) | Transient speech (m) |
| 1.0mm2 copper | 49 | 57 |
| 2.5mm2 copper | 67 | 85 |
| 4.0mm2 copper | 70 | 91 |
| 1.8mm2 flat copper tape | 87 | 101 |
Inputs:
| Input 1 | Input 1 Balanced Mic, balanced or unbalanced line Input impedance 10kΩ per side Min level (MIC / Line -73dBu / -31dBu Max level (MIC / Line) -37dBu / +5dBu Phantom voltage MIC only +12V |
| Input 2 | Isolated 100V line or low impedance mono or stereo speaker Input impedance 100V Line / spkr 120kΩ / 7.8kΩ Min level 100V Line / spkr +14dBu / -9dBu Max level 100V Line / spkr >+47dBu / >+27dBu |
| Input 3 | Isolated 100V line or low impedance mono or stereo speaker Input impedance 100V Line / spkr 120kΩ / 7.8kΩ Min level 100V Line / spkr +14dBu / -9dBu Max level 100V Line / spkr >+47dBu / >+27dBu |
| AC power input supply | 230V 30Ws 45-65Hz 110V option available Connected via chassis mounted screw terminal block |
| Input fuse | T250mA |
Outputs:
| Drive voltage | >7.1VRMS – 10.0Vpk |
| Drive Current | 1kHz sine wave >4.9ARMS 7.0Apk Continuous pink noise 2.3ARMS 7.0Apk Short term peaks >7ARMS 10Apk |
| Minimum Loop Resistance | 0.2Ω |
| Maximum Loop Impedance | 1.3Ω |
THERMAL HEAT CHART
| Idle | 1/6 peak Output Current | 1/3 peak Output Current | Full Power | ||||||||
| Driver | Channels | Current (ARMS) | Load Resistance (Ohms) | AC In (W) | BTU | AC In (W) | BTU | AC In (W) | BTU | AC In (W) | BTU |
| CLS1 | 1 | 3.5 | 1.0 | 4 | 14 | 15 | 47 | 27 | 77 | 45 | 111 |
| CLS2 | 1 | 4.9 | 1.0 | 5 | 17 | 19 | 58 | 35 | 91 | 63 | 131 |
Audio system:
| Frequency Response | 80Hz to 6.3kHz ±3dB |
| Distortion | THD+N |
| Automatic Gain Control | (AGC) Optmised for speech. Dynamic range >36dB |
| Metal loss correction | (MLC) 0 to 3dB per octave frequency correction (1kHz remains constant). Control mounted on PCB. |
Physical:
| Cooling | Natural convection |
| Environment | IP20, -10°C to +40°C |
| Dimensions | W, H, D: 200mm, 200mm, 44mm |
| Weight | 1.8kg |
| Mounting | Wall mounting, secured by 4 screws |


