
Açıklama

W5-2, özellikle AV rafı ve ağ izleme gereksinimlerinin olmadığı, ancak yine de Ampetronic'in sektör lideri ses sızıntısı kontrol tasarımından yararlanabilen küçük odalar için tasarlanmıştır.
Özellikle küçük odalarda düşük ses sızıntısı için tasarım şablonları, Loopworks portalından buradan indirilebilir. Bunlar, daha yüksek kayıplı ortamlar için çift çekirdekli düz bakır bantlı iki dönüş seçeneği de dahil olmak üzere, özellikle W5-2 için optimize edilmiştir.
Özellikler
- Giriş 1 ve 2 – 3 yollu 3,5 mm euroblok vidalı terminal girişi
- Dengeli mikrofon/hat seçilebilir
- 100V hat girişi – 2 yollu 5 mm euroblok vidalı terminal
- Fantom Güç – 24V (her iki kanalda da değiştirilebilir)
- Döngü Çıkış Sürüş Akımı – W5-2 – kanal başına 5A RMS
- Döngü Çıkış Konnektörleri – kanal başına 2 yollu 5 mm euroblok vidalı terminal
- Dahili Test Tonları (1 kHz sinüs, Pembe gürültü)
- Faz kayması – 90° (her zaman açık)
- Metal Kaybı Düzeltmesi – oktav başına 0 ila 3 dB frekans düzeltmesi (1 kHz sabit kalır)
- Üç aşamalı endüktans kompanzasyonu – farklı döngü uzunluklarıyla frekans tepkisini düzeltmek için
- DC Çıkışı – 24V DC
Teknik özellikler
| INPUTS & SIGNAL PROCESSING | MIC | Line | UNITS |
| Input figures quoted at maximum front panel gain control setting. | |||
| INPUT 1 & 2: (mic/Line) 3 way, 3.5mm phoenix, balanced, suitable for up to 600Ohm microphones or line level.
|
|
|
|
| Input impedance | 8,700 | 8,700 | Ω |
| Sensitivity | -69 | -45 | dBu |
| Overload | -33 | -9 | dBu |
| 100V: Isolated 100V line input |
|
|
| Input impedance | 120,000 | Ω |
| Sensitivity | +11 | dBu |
| Overload | +47 | dBu |
| AGC: Compression of signal indicated by green INPUT LED when active and RED when overloaded. |
|
|
| Input range | >36 | dB |
| Output range | ±1 | dB |
| Min. input level for AGC | See sensitivity |
|
| Attack time | 3.5 | ms |
| Decay time | 1.4 | s |
| METAL LOSS CORRECTION: Specially designed adjustable filter to compensate for the effects of metal loss. Gain @ 1kHz remains constant. |
|
|
| Min. slope | 0 | dB/oct. |
| Max. slope | +3 | dB/oct. |
| LOOP IND: High shelf filter options to compensate for the effect of loop inductance on the class D output stage |
| |
| Low | No effect | |
| Med | 3dB max starting from ~1kHz | |
| High | 4.8dB max starting from ~1kHz | |
| Test Signals: Internally generated signals for commissioning which when activated interrupt the input audio signal. |
|
|
| Off | Audio signal passed |
|
| Field | Single 1k tone | Hz |
| Freq | Combined 100, 1k & 5k sine tones | Hz |
| DC Power | ||
| Power figures for reference only. With unit set for maximum output with the input in AGC. Only use the provided DC power supply. | ||
| Voltage | 24 | V |
| Current idle | 0.28 | A |
| Current pink noise | 1.3 | A |
| Current sine | 3.2 | A |
| OUTPUTS | UNITS | |
| LOOP OUTPUT: 2x 2way, 5mm, phoenix. | ||
| Voltage | 7.8 | VRMS |
| Current | 5 | ARMS |
| Continuous pink noise | 2.5 | ARMS |
| THD +N (1kHz, sine, max output) | 0.5 | % |
| Maximum loop resistance | 0.6 (at maximum current) | Ω |
| Frequency response | ±3dB, 100 to 5000Hz | |
| DC OUT: 2 way, 3.5mm, Phoenix. Fuse protected output for ancillary devices. | ||
| Voltage | 24 | V |
| Current | 0.1 | A |
| Status:2 way, 5mm, Phoenix. Volt free relay contacts indicating fault condition when open. |
| |
| Contact rating (resistive load) | 12A, 125Vac | |
|
| 10A, 250Vac | |
|
| 10A, 30Vdc |
| PROTECTION FEATURES | UNITS | ||
| Thermal Protection: If the PA amplifier reaches a pre-determined level the | |||
| output current will be gradually attenuated followed by shutdown. | |||
| Output attenuation | Max -4dB @ 90 | °C | |
| Unit shutdown (Requires power cycle to recover) | PA chip junction temp>155 °C | °C | |
| DC input over-current | Output attenuation | Max 4dB >5A dc input | |
| Output over-current | Unit shutdown (Requires power cycle to recover) | >10A loop current |
| PHYSICAL CHARACTERISTICS | UNITS | |
| Dimensions: Width | 270 | mm |
| Height | 152 | mm |
| Depth | 42 | mm |
| Weight | 1.1 | kg |
| Operating temperature | -10 to 40 | °C |
| Ingress protection rating | 30 | IP |


